Canal Comments-The Saga at Sandyville, Part 1 – by Terry K. Woods

Terry’s introduction.

The ‘doings’ of the Lessees, those 21 or 23 men who “administered” to the canals from June of 1861 into December of 1878 has always been a bit nebulous. And just where was the demarcation line between the duties of the State Board of Public Works and the Lessees? They both had Board Members and they both had Resident Engineers. These next two columns on the Saga at Sandyville will do nothing to clear things up. You will see, perhaps, that even those ‘on the scene’ were absolutely confused.

In the meantime, now that Spring is here, it is time to get out along the canal routes and find those artifacts and structures that you always felt, “the next time I get out in the field I’ll find it”. Lock 29 on the western division of the S. & B., is featured in the next two columns. That site I’ve found, and lost and found, and, . . .but you get the idea.

SAGA AT SANDYVILLE

James Kelly of Cuyahoga County, had been a prolific contractor on the Sandy & Beaver Canal on all three of its divisions. Then, after the collapse of the Cold Run Reservoir embankment in early 1852, he was hired by the canal company for the unenviable job of “trouble-shooter,” to pay off the ever increasing number of creditors with the ever decreasing amount of incoming funds.

By mid-1853, it had become obvious that no miracle concerning the Sandy & Beaver Canal Company was forthcoming. All the surplus real-estate with any value had already been sold. All that remained was the canal right-away itself and a few unencumbered water rights. Kelly had done what he could by spreading the smaller and smaller amounts of cash that canal tolls brought in from time to time to squelch the screams of the more voracious creditors.

Kelly had probably taken on, and completed, more contracts in building the canal than anyone else. More than half of his payments had been in “company bonds.” Kelly, in his current position was well aware that the canal company was going under and decided that if he wanted anything from the collapse he had better get it quickly.

Therefore, in early 1853, James Kelly initiated a law suit against the Sandy & Beaver Canal Company for his back wages. An avalanche of claims followed and the Sandy & Beaver Canal Company declared bankruptcy on June 28, 1853. On March 6, 1854, at a master commissioner’s sale in New Lisbon, that portion of the Sandy & Beaver Canal within the State of Ohio was divided into 82 Parcels and auctioned off.

As payment for his suit against the company, Kelly asked for, and was awarded, parcels 80, 81 and 82 of the Sandy & Beaver Canal. This line ran from two rods above lock 29 in Sandyville to the junction with the Ohio & Erie Canal in Bolivar, which was approximately six miles in lenght. The deed for this land and water-rights was transferred to Kelly on March 7, 1856.

Sandyville had prospered during its brief encounter with the active Sandy & Beaver Canal. The grist mill at the southern edge of town powered by the canal was a receiver and shipper on the canal, as were several coal mines that had sprung up in the area. A group of local citizens set about to get their link to the outside world reattached. A man by the name of William Nelson appears to have been the spokesman for the group. Shortly after Kelly had received his deed, or perhaps even before, Nelson had contacted the State’s Board of Public Works to ascertain if they had any interest in obtaining that six miles of the S & B as a “feeder” to the Ohio Canal. Their only stipulation was that the State maintain the waterway so it could carry traffic into and out of Sandyville. Kelly sold his S. & B. canal lands and water-rights to the group from Sandyville for $5,000 on August 2, 1856.

The 1912 Topo map. The Ohio and Erie can be seen running through Bolivar.

The Board of Public Works had the waterway examined and surveyed. They reported that the wooden aqueduct across the Tuscarawas River leading to the junction with the Ohio Canal at Bolivar, and the lock at the head of the long slackwater pool below Sandyville, were both in poor condition. In addition, the canal banks had been cut in several places by local residents wishing to regain access to their lands cut off by the canal. After some deliberation, the Board agreed to take over the canal if the banks were first repaired. On December 29, 1856, for the sum of $1.00, the western-most six miles of the Sandy & Beaver Canal became a feeder to and part of the Ohio & Erie Canal.

The final description of the portion of the S & B that became part of the State’s canal system, however, only included that portion from below Lock 29 in Sandyville to Bolivar. That was a small shortening of a bit over 2 rods, but it placed the Sandyville terminus approximately a quarter of a mile below the warehouses in the village. Either that discrepancy went unnoticed or the actual foreshortening didn’t seem that important at the time.

There was some business on that portion of the canal after the turnover. The Public Works report for 1859 stated that up until August of that year the Sandy & Beaver feeder had carried 33,000 bushels of wheat, 41,000 feet of lumber, and 3,213 tons of coal out of the village and 278 barrels of salt, lime and fish and 91,400 feet of lumber into it. The shortened boating season was the result of a collapse of a portion of the wooden aqueduct at Bolivar. A statement from a boatman’s diary in 1863 indicates that at least one trip was made into Sandyville that year.

So Sandyville was connected to the outside world via the Sandy & Beaver Feeder. BUT, in 1868 the following resolution was offered in the Ohio State Congress, . . . . .

“H.R. No. 111: Whereas the citizens of Sandyville and vicinity petitioned the Ohio Legislature authorizing the State of Ohio to adopt, as part of the public works, that portion of the Sandy & Beaver Canal which lies between Bolivar and Sandyville as a navigable feeder to the Ohio Canal; and whereas an Act was passed the 9th. Of April, 1856, adopting it on condition that the owners of said canal should put that part of the canal in good repair, and whereas, in pursuance of the inducement held out by such Legislative Act, and the construction put on it by the people of Sandyville and vicinity, they, for the purpose of having communication with the Ohio Canal, expended $7,000 in buying the right of way, paying (wages?) and putting said feeder in good repair; and whereas, afterwards the Board of Public Works, in their resolution of acceptance, only accepted that portion of the canal between Bolivar and the lock at the head of the slackwater pool, and so construed the law so as not to include the said lock and, whereas, by reason of such constriction the work is entirely valueless to the people of Sandyville and vicinity, as they have no connection with the Ohio Canal and derive no benefit from the expenditure of said money, therefore, “Resolved” – That the committee on Public Works be and is hereby Instructed to inquire into the justice and validity of said claim, and report to the House by Bill or otherwise”.

Such a Bill was rendered by the House during the 1869/70 Session to repair Sandyville Lock just above the Sandy & Beaver feeder and make it passable for canal boats. The Bill also authorized an amount of ‘up to’ $3,000 for the repair of the lock.

The group of Sandyville citizens that had bought that canal section from Kelly and handed it over to the State 14 years before, legally, still owned that section containing the lock that the State had not accepted. The canal above the lock belonged to owners of the Sandyille grist mill. They should have been a part of the current group agitating to repair the lock. Subsequent events, however, proved that wasn’t true. So what came next is an extremely convoluted, though interesting, story – and the subject of a future column.

i Maretta College, Special Collection, transcribed by George S. Hackett, December 05, 2003.

The Welker Feed Mill – Canal Comments

By Terry K Woods

Today’s column is of a mill once operated by water from a section of the Sandy & Beaver Canal in Tuscarawas County. It was written from a taped interview in 1975 with the one time owner of the mill in Sandyville. (1)

Now Sandyville, in itself, is a very interesting place. When the Bolivar Dam was erected in the mid 1930s this town was literally moved to higher ground. As a result, it is very difficult (spelled IMPOSSIBLE) to locate much of the canal or any artifacts in this area.

The foundation to the mill can be found and a a bit of that part of the canal that was used as the mill race until 1935 but very little else. There was a lock (No 29) in or near the town. It was rebuilt by the Lessees in 1872, but I have not been able to confidently determine its location.

I’ve spent a lot of time over the past 40 years scouring the area for that lock location. Last March I spent a portion of three days down there. As I say, I’m not sure I know the exact location, though I thought I found it once in 1985.

THE WELKER FEED MILL ON THE SANDY & BEAVER CANAL

Our mill was located near the bend in the Big Sandy Creek just to the southeast of the old center of the village of Sandyville. One cornerstone of the mill bore the date 1836. That was also the year in which the Sandy & Beaver Canal was being built across the northern portion of Tuscarawas County.

The canal crossed Nimishillen Creek in a slack-water pool a half-mile east of the mill. Even after boats stopped using the canal, the dam across the Nimishillen provided a steady water supply to run the mill and the guard lock on the west bank of the creek acted as head gates to the mill race. The mill race consisted of a half-mile of the Sandy & Beaver Canal bed and a channel of a 100 yards or so that had been dug at right angles to the canal. The mill sat between the canal and the Big Sandy and our tail race flowed right into that creek.

I don’t know who built the mill originally. I think a man named Rolland or Voelum owned it at one time. There was also a McKinney mixed up in it somewhere. The way we got it was that my grandfather had gone in on a fellow’s note and had to make it good when that fellow defaulted. The only way my grandad could get anything out of that deal was to take over the mill. That was in 1893. My dad, Theodore “Dory” Welker, moved into the mill in 1894. It wasn’t running then and he had an awful time making it go.

He hired professional millers because he wasn’t one himself. Finally, around 1900, there was an old guy by the name of Charlie Seibert. He came to our place looking for a job and my dad took him in. He was a miller personified and knew all about the milling business. He just kind of made his home with us for the next 25 years. Occasionally some big company would have trouble with their mill and Old Charlie would leave us for a while until it straightened out, but he always came back to our place. He kept that old mill running “like an Ingersoll”.

Dad originally called the mill the “Sandy Valley Roller Mill,” but it was known mostly as the Welker Feed Mill. I spent all of my boyhood along the canal and must have skated a million miles between our mill and the dam and back. The Canton cut-off (otherwise known as the Nimishillen &Sandy Canal) joined the Sandy & Beaver Canal along our section. They joined at right angles to each other. You could plainly see the towpath and that the channel was intended to be a canal, though I don’t know if it ever held water. I did a lot of trapping for skunk and the like in that cut-off when I was a boy.

I joined Dad in running the mill in 1918. Sometime between 1920 and 1925 we rebuilt the dam and guard lock. We replaced the original wood and rubble dam with one of concrete 154-feet-long. The eastern end of the new dam rested on the original stone abutments of canal days, but the western end rested on the earthen embankment of the creek. The western stone abutment from canal days lies 50 yards or so west of the concrete dam. At the time we installed a concrete head gate at the lock. The original wooden gates were still fairly intact. The lock chamber had been lined with wood and most of the planking was still in pretty good shape.

During the Depression, we ran the mill from 6:00 in the morning until midnight and never took in a dollar! Everything was done by barter and the only way we could tell our profit was to see how big a pile of wheat we had.

I was never too interested in the history of the canal when I was a boy, but I do remember the “Old Timers” telling about the old canal warehouses. I believe there were two that stood along each bank of the canal near the center of the old town near where our mill race left the main canal. They both burned down in 1898 and some say the fires were deliberately set to get rid of them.

When I was a young man, the B. & O. had a spur running from the Sandyville Station into Magnolia. A train went to Magnolia maybe two or three times a week to take groceries, pick up milk, and distribute the few passengers who wanted to go from one town to another. That train consisted of an engine and one car that carried passengers in one end and luggage and freight in the other. You could see a lot of the old canal from that train, maybe you still could, because those bottoms up there are really in no man’s land.

The State built the Bolivar Dam on the Big Sandy in 1936 and the old village and mill were moved to higher ground. That part of the mill that had been built out over the water was torn down and the rest moved to its present location in the northwest corner formed by the B. & O. Railroad and Route #183. The B. & O. tracks were also moved to higher ground and now cross the plain on a high earthen fill. That embankment now covers the junction of the Sandy & Beaver Canal and the Canton cut-off but you can still see faint traces of the cut-off as it comes out from under the railroad embankment and heads north.

Shortly after the mill was closed someone, probably disgruntled farmers, dynamited the dam – blew the whole center out of it. You can still find the ends of the dam as well as both original stone abutments and what remains of the guard lock. The foundation of the mill is still there at the end of the race. In 1933 we had built a new penstock and, in the winter, when there is not much foliage, it should be easy to find.

The mill had two turbine wheels; one rated at 43 h.p. and the other at 36 h.p. Both ratings were with nine feet of water. When we closed the mill we pulled both wheels out and sold one to Mr. Wilson whose mill is still up along the Ohio Canal in Cuyahoga County. He wanted the other wheel but when we went down there one day we found someone had broken the wheel up with sledges and hauled the chunks of cast iron over the mill race and away. The Depression was still going pretty strong and they probably wanted what money that wheel would bring for scrap.

My son Bob, came into the business in 1947 after serving in the Army. Dad died in1950 and Bob and I continued in the feed business until the Fall of 1972 when the warehouse was sold to the Morrison Brothers.

(1) As told to Terry Woods (on tape) during a hike in the area in the early spring of 1975.